Pass4sure Cisco Certification

Interconnecting Cisco Networking Devices Part 2

Exam Number: 640-816 ICND2
Associated Certifications: CCNA
Duration: 75 minutes (45-55 questions)
Available Languages: English
Click Here to Register: Pearson VUE
Exam Policies: Read current policies and requirements
Exam Tutorial: Review type of exam questions

Exam Description Exam Topics Recommended Training Additional Resources
Exam Description
The 640-816 Interconnecting Cisco Networking Devices Part 2 (ICND2) is the exam associated with the Cisco Certified Network Associate certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.0 course. This exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small to medium size enterprise branch network. The exam covers topics on VLSM and IPv6 addressing; extending switched networks with VLANs; configuring, verifying and troubleshooting VLANs; the VTP, RSTP, OSPF and EIGRP protocols; determining IP routes; managing IP traffic with access lists; NAT and DHCP; establishing point-to- point connections; and establishing Frame Relay connections.

Exam Topics
The following topics are general guidelines for the content likely to be included on the Interconnecting Cisco Networking Devices Part 2 exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.

Configure, verify and troubleshoot a switch with VLANs and interswitch communications
Describe enhanced switching technologies (including: VTP, RSTP, VLAN, PVSTP, 802.1q)
Describe how VLANs create logically separate networks and the need for routing between them
Configure, verify, and troubleshoot VLANs
Configure, verify, and troubleshoot trunking on Cisco switches
Configure, verify, and troubleshoot interVLAN routing
Configure, verify, and troubleshoot VTP
Configure, verify, and troubleshoot RSTP operation
Interpret the output of various show and debug commands to verify the operational status of a Cisco switched network
Implement basic switch security (including: port security, unassigned ports, trunk access, etc.)
Implement an IP addressing scheme and IP Services to meet network requirements in a medium-size Enterprise branch office network
Calculate and apply a VLSM IP addressing design to a network
Determine the appropriate classless addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN environment
Describe the technological requirements for running IPv6 (including: protocols, dual stack, tunneling, etc)
Describe IPv6 addresses
Identify and correct common problems associated with IP addressing and host configurations
Configure and troubleshoot basic operation and routing on Cisco devices
Compare and contrast methods of routing and routing protocols
Configure, verify and troubleshoot OSPF
Configure, verify and troubleshoot EIGRP
Verify configuration and connectivity using ping, traceroute, and telnet or SSH
Troubleshoot routing implementation issues
Verify router hardware and software operation using SHOW & DEBUG commands
Implement basic router security
Implement, verify, and troubleshoot NAT and ACLs in a medium-size Enterprise branch office network.
Describe the purpose and types of access control lists
Configure and apply access control lists based on network filtering requirements
Configure and apply an access control list to limit telnet and SSH access to the router
Verify and monitor ACL’s in a network environment
Troubleshoot ACL implementation issues
Explain the basic operation of NAT
Configure Network Address Translation for given network requirements using CLI
Troubleshoot NAT implementation issues
Implement and verify WAN links
Configure and verify Frame Relay on Cisco routers
Troubleshoot WAN implementation issues
Describe VPN technology (including: importance, benefits, role, impact, components)
Configure and vary PPP connection between Cisco routers

Question: 1
Refer to the exhibit.

A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)

A. The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
B. Address translation on fa0/1 is not required for DMZ Devices to access the Internet. C. The fa0/1 IP address overlaps with the space used by s0/0.
D. The fa0/1 IP address is invalid for the IP subnet on which it resides.
E. Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown.
Answer: B, E Question: 2
Refer to the exhibit.

TK

Exam Name: Interconnecting Cisco Networking Devices Part 2
Exam Type: Cisco Case Studies: 2
Exam Code: 640-816 Total Questions: 136

Which statement describes DLCI 17?

A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
Answer: C Question: 3
What is the default Local Management Interface frame type transmitted by a Cisco router on a
Frame Relay circuit?

A. Q933a B. B8ZS C. IETF D. Cisco E. ANSI
Answer: D Question: 4
Refer to the exhibit.

The network shown in the exhibit has just been installed.
Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?

TK

Exam Name: Interconnecting Cisco Networking Devices Part 2
Exam Type: Cisco Case Studies: 2
Exam Code: 640-816 Total Questions: 136

A. Host B should be in VLAN 13.
B. The address of host C is incorrect.
C. The gateway for host B is in a different subnet than the host is on.
D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E. The switch port connected to the router is incorrectly configured as an access port.
Answer: B Question: 5
Routing has been configured on the local router with these commands:

Local(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1
Local(config)# ip route 10.1.0.0 255.255.255.0 192.168.2.2
Local(config)# ip route 10.1.0.0 255.255.0.0 192.168.3.3

Drag each destination IP address on the left to its correct next hop address on the right.

Answer:

Question: 6
Refer to the exhibit.

TK

Exam Name: Interconnecting Cisco Networking Devices Part 2
Exam Type: Cisco Case Studies: 2
Exam Code: 640-816 Total Questions: 136

The router has been configured with these commands:

hostname Gateway interface FastEthernet 0/0
ip address 198.133.219.14 255.255.255.248
no shutdown
interface FastEthernet 0/1
ip address 192.168.10.254 255.255.255.0
no shutdown interface Serial 0/0
ip address 64.100.0.2 255.255.255.252
no shutdown
ip route 0.0.0.0 0.0.0.0 64.100.0.1

What are the two results of this configuration? (Choose two.)

A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers. D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address translation.
Answer: D, E Question: 7
Refer to the exhibit.

Free 640-816 Exams’s PDF Download
Free Testking offers free demo for 640-816 PDF(Interconnecting Cisco Networking Devices Part 2). You can check out the interface, question quality and usability of our practice exams . We are the only one site can offer demo for almost all Interconnecting Cisco Networking Devices Part 2.

Recommended Training about 640-816 exam PDF
The following courses are the recommended training for 640-816 exam PDF.
640-816 Q & A with Explanations
640-816 Audio Exam
640-816 Study Guide
640-816 Preparation Lab

Exam Number/Code: 640-816
Exam Name: Interconnecting Cisco Networking Devices Part 2

“Interconnecting Cisco Networking Devices Part 2″, also known as 640-816 exam, is a Cisco certification.
Preparing for the 640-816 exam? Searching 640-816 Test Questions, 640-816 Practice Exam, 640-816 Dumps?

With the complete collection of questions and answers, Pass4sure has assembled to take you through 147 Q&As to your 640-816 Exam preparation. In the 640-816 exam resources, you will cover every field and category in CCNA helping to ready you for your successful Cisco Certification.

Questions and Answers : 147 Q&As
Updated: March 16th , 2008
Market Price: $125.99
Member Price: $99.99

pass4sure 640-816 ICND2
Interactive Testing Engine Included!
469 Questions
Updated : 09/18/2008
Price : $76.99 $69.99

Free download?pass4sure 640-816 ICND2
Free download?testking 640-816 ICND2

PassGuide Braindumps: provides high quality Cisco exam practice questions and Training Materials.Hel you Pass Cisco Certifications

Download Free Latest Pass4sure P4S PassForsure Braindumps

1. Free Pass4sure cisco ccna 640-802 473 Q&a
2. Free Pass4sure 640-802 CCNA 2.73
3. Free Pass4sure 640-822 ICND1 2.83
4. Free Pass4sure 350-022 CCIE 2.83
5. Free Pass4sure 642-503 SNRS 2.93
6. Free Pass4sure 350-026 CCIE 2.95
7. Free Pass4sure 642-812 BCMSN 2.93
8. Free Pass4sure 642-587 AWLANFE 2.73
9. Free Pass4sure 642-356 CSSSS 2.93
10. Free pass4sure 642-901 BSCI 2.73